Hot Selling for 22641-T Swaged Hose Fiting to Barcelona Importers
Hot Selling for 22641-T Swaged Hose Fiting to Barcelona Importers Detail:
45° BSP O’RING FEMALE 60° CONE
PART NUMBER |
HOSE
|
THREAD T |
B mm |
L mm |
A mm |
M mm |
H2 mm |
||
|
DN |
In |
SIZE |
|
|
|
|
|
|
S226C1 – 04 – 04OR | 6 | 1/4″ | 04 | 1/4″ – 19 | 4 | 35,2 | 5,2 | 14,7 | 19 |
S226C1 – 06 – 06OR | 10 | 3/8″ | 06 | 3/8″ – 19 | 7 | 40,9 | 6 | 17,3 | 22 |
S226C1 – 08 – 08OR | 12 | 1/2″ | 08 | 1/2″ – 14 | 9,3 | 47,6 | 6,5 | 19,9 | 27 |
S226C2 – 10 – 10OR | 16 | 5/8″ | 10 | 5/8″ – 14 | 12 | 56,8 | 9,7 | 25,8 | 30 |
S226C2 – 12 – 12OR | 20 | 3/4″ | 12 | 3/4″ – 14 | 15 | 67,8 | 9 | 30,3 | 32 |
S226C2 – 16 – 16OR | 25 | 1″ | 16 | 1″ – 11 | 19,5 | 84,4 | 10,5 | 37,4 | 38 |
S226C2 – 16 – 20OR | 25 | 1″ | 16 | 1.1/4″ – 11 | 26 | 90,1 | 10,1 | 41,6 | 50 |
S226C2 – 20 – 20OR | 32 | 1.1/4″ | 20 | 1.1/4″ – 11 | 26 | 100,7 | 10,1 | 44,8 | 50 |
S226C2 – 20 – 24OR | 32 | 1.1/4″ | 20 | 1.1/2″ – 11 | 32 | 101,3 | 12,5 | 45,5 | 55 |
S226C2 – 24 – 24OR | 40 | 1.1/2″ | 24 | 1.1/2″ – 11 | 32 | 112,5 | 12,5 | 49 | 55 |
S226C2 – 24 – 32OR | 40 | 1.1/2″ | 24 | 2″ – 11 | 42 | 116 | 16,1 | 52,5 | 70 |
S226C2 – 32 – 32OR | 50 | 2″ | 32 | 2″ – 11 | 42 | 132,9 | 16,1 | 55,7 | 70 |
Product detail pictures:
Related Product Guide:
Understanding Hydraulic Hose Fittings
Tube Fittings and Pipe Fittings – Double Ferrule Tube Fittings
Assume full responsibility to meet all demands of our clients; achieve continuous advancements by promoting the growth of our clients; become the final permanent cooperative partner of clients and maximize the interests of clients for Hot Selling for 22641-T Swaged Hose Fiting to Barcelona Importers, The product will supply to all over the world, such as: Rio de Janeiro, Australia, Peru, In order to meet more market demands and long-term development, a 150, 000-square-meter new factory is under construction, which will be put into use in 2014. Then, we shall own a large capacity of producing. Of course, we will continue improving the service system to meet the requirements of customers, bringing health, happiness and beauty to everyone.
I decided to make a jaw crusher to process some construction debris I had laying around. I began the project with the idea that it would be mobile. I started with an old boat trailer and started building accordingly. I used pillow blocks and 2 bolt flanges to support the 1.5″ driveshaft. The jaw has 3/4″ swing at the top and about 1/2″ an inch at the bottom. It uses a 5 hp briggs engine for power, a trailer tire and rim for a flywheel, and a yamaha blaster chain drive hub with the sprocket removed.
By Adam from Liberia - 2017.02.14 13:19
The enterprise has a strong capital and competitive power, product is sufficient, reliable, so we have no worries on cooperating with them.
By Hannah from Iraq - 2018.02.04 14:13