Factory supplied DIN EN853 1SN-2SN Wholesale to Guyana

Short Description:

FERRULE FOR SAE 100R1AT – R2AT / DIN EN 853 1SN – 2SN / SAE 100R16 SAE 100R17   PART NUMBER HOSE D mm L mm   DN In SIZE     S05000 – 03 5 3/16″ 03 20 23,5 S05000 – 04 6 1/4″ 04 23 30 S05000 – 05 8 5/16″ 05 24 30 S05000 – 06 10 3/8″ 06 26 32 S05000 – 08 12 1/2″ 08 29 34 S05000 – 10 16 5/8″ 10 33 37 S05000 – 12 20 3/4″ 12 37 42 S05000 – 16 25 1...


Product Detail

Product Tags

Related Video

Feedback (2)

Bear "Customer first, Excellent first" in mind, we work closely with our shoppers and supply them with efficient and specialist services for Ferrule For 4SH Hose , Wire Braid Hose , Hydraulic Connectors , We sincerely welcome the two foreign and domestic business enterprise companions, and hope to operate with you in the close to long term!
Factory supplied DIN EN853 1SN-2SN Wholesale to Guyana Detail:

FERRULE FOR SAE 100R1AT – R2AT / DIN EN 853 1SN – 2SN / SAE 100R16 SAE 100R17

32

 

PART NUMBER

HOSE

D

mm

L

mm

 

DN

In

SIZE

 

 

S05000 – 03 5 3/16″ 03 20 23,5
S05000 – 04 6 1/4″ 04 23 30
S05000 – 05 8 5/16″ 05 24 30
S05000 – 06 10 3/8″ 06 26 32
S05000 – 08 12 1/2″ 08 29 34
S05000 – 10 16 5/8″ 10 33 37
S05000 – 12 20 3/4″ 12 37 42
S05000 – 16 25 1″ 16 46 51
S05000 – 20 32 1.1/4″ 20 59 59
S05000 – 24 40 1.1/2″ 24 67 67
S05000 – 32 50 2″ 32 80 72

Product detail pictures:

Factory supplied
 DIN EN853 1SN-2SN Wholesale to Guyana detail pictures


Related Product Guide:
Things to Know About Pipe Fitting Works
Importance of PVC Fittings

We support our customers with ideal premium quality products and solutions and superior level assistance. Becoming the specialist manufacturer in this sector, now we have received rich practical experience in producing and managing for Factory supplied DIN EN853 1SN-2SN Wholesale to Guyana, The product will supply to all over the world, such as: Israel , Hyderabad , Plymouth , We've been persisting in the business essence "Quality First, Honoring Contracts and Standing by Reputations, providing customers with satisfying products and service. " Friends both at home and abroad are warmly welcome to establish everlasting business relations with us.


  • An Introductory Guide to Installing a Septic Tank and Drainfield (English) – New Mexico State University 2005 – – Video furnished by Media Productions, New Mexico State University. Noncommercial use only. Wastewater from home not only causes unpleasant odors, but also contains impurities and pathogens, which contaminate drinking water and cause serious health problems. This video shows you step by step how to properly install a home sewage treatment system, consisting of a septic tank and a drainfield, to help protect the health of you and your loved ones.



    The RCBS Case Prep center can be fitted with a Lee Case Trimmer Cutter that has been slightly modified (see below) and a Lee Case Length Gage. This adds trimming to the list of case preparation functions and allows the RCBS Case Prep Center to do almost everything that needs to be done to a piece of brass. Tumble clean the brass, process the brass through the multiple stages on the RCBS Case Prep Center and it’s ready to be reloaded with a primer, powder and bullet. Approximately 150 brass cases can be processed in an hour, including trimming to length, chamfering inside and outside the case neck and preparing the primer pocket. The Hornady Primer Pocket Reamer Cutter Head reams the primer pocket to the correct diameter, including the removal of any military primer pocket crimp, and chamfers the entrance to the primer pocket to facilitate the entry of the new primer into the primer pocket. Redding makes a very nice primer pocket uniformer that will ream the primer pocket to the proper diameter and also cut the primer pocket to the correct depth. The Redding Primer Pocket Uniformer is a bit pricey at $30, but carbide cutting tools are expensive. They also last a long time.

    NOTE ABOUT THE MODIFIED CUTTER:

    I drilled and tapped one cutter for me and it was a little hard but not a problem for a sharp high speed steel drill on my little mill-drill. I did one for a friend and it was very difficult. The steel cutter was very hard. I think Lee makes the cutters from a tool steel that they subsequently induction heat treat, and I think my initial cutter wasn’t properly heat treated which probably explained why it dulled so quickly cutting brass.

    I eventually used a cobalt drill, low RPM and a lot of pressure to drill the hardened steel. I used a much larger center drill to start the hole because the #29 tap drill for 8-32 would walk long before drilling. The center drill is much shorter and fatter and therefore stiffer. Once I had a divot started, I drilled the tap hole. I almost broke a tap, so I drilled a larger hole for much less thread engagement and tapped that larger hole. I think the thread engagement was so little that I epoxied the stud in place?

    I now recommend getting a scrap chunk of aluminum or plastic, drill a #29 hole all the way through the center, use that as the pilot hole to drill a much larger hole part way through that’s just barely large enough for the cutter body and epoxy it in place after tapping the #29 hole on the base and screwing in a #8-32 screw from the inside so the threads stick out the bottom by 3/8″ or so.

    http://www.midwayusa.com/viewproduct/?productnumber=617234

    http://www.midwayusa.com/viewproduct/?productnumber=253550

    http://www.midwayusa.com/viewproduct/?productnumber=729748

    The factory has advanced equipment, experienced staffs and good management level, so product quality had assurance, this cooperation is very relaxed and happy!
    5 Stars By Alexia from Moscow - 2016.12.02 14:11
    The company can keep up with the changes in this industry market, product updates fast and the price is cheap, this is our second cooperation, it's good.
    5 Stars By Mamie from Jordan - 2015.06.19 10:42

    Related Products

    WhatsApp Online Chat !