Factory selling 90011-Swaged Hose Fiting for Boston Importers

Short Description:

CONNECTOR INSERT    PART NUMBER HOSE B mm L mm   DN In SIZE     S900A0 - 03 - 03 5 3/16″ 03 3 13,2 S900A0 - 04 - 04 6 1/4″ 04 4 14 S900A0 - 05 - 05 8 5/16″ 05 5,5 14 S900A0 - 06 - 06 10 3/8″ 06 7 15,2 S900A0 - 08 - 08 12 1/2″ 08 9,3 15,6 S900A0 - 10 - 10 16 5/8″ 10 12 15,6 S900A0 - 12 - 12 20 3/4″ 12 15 18 S900A0 - 16 - 16 25 1″ 16 19,5 22,6 S900A0 - 20 - 20 32 1.1/4″ 20 26 23 S900A0 - 24 - 24 ...


Product Detail

Product Tags

Related Video

Feedback (2)

We depend on sturdy technical force and continually create sophisticated technologies to satisfy the demand of Split Flange Fittings , Ferrule For 4SP Hose , Hydraulic Tubing , We are going to empower people by communicating and listening, Setting an example to others and learning from experience.
Factory selling 90011-Swaged Hose Fiting for Boston Importers Detail:

CONNECTOR INSERT

5

 

 PART NUMBER HOSE B

mm

L

mm

  DN In SIZE    
S900A0 - 03 - 03 5 3/16″ 03 3 13,2
S900A0 - 04 - 04 6 1/4″ 04 4 14
S900A0 - 05 - 05 8 5/16″ 05 5,5 14
S900A0 - 06 - 06 10 3/8″ 06 7 15,2
S900A0 - 08 - 08 12 1/2″ 08 9,3 15,6
S900A0 - 10 - 10 16 5/8″ 10 12 15,6
S900A0 - 12 - 12 20 3/4″ 12 15 18
S900A0 - 16 - 16 25 1″ 16 19,5 22,6
S900A0 - 20 - 20 32 1.1/4″ 20 26 23
S900A0 - 24 - 24 40 1.1/2″ 24 32 23
S900A0 - 32 - 32 50 2″ 32 42 25,8

Product detail pictures:

Factory selling
 90011-Swaged Hose Fiting for Boston Importers detail pictures

Factory selling
 90011-Swaged Hose Fiting for Boston Importers detail pictures


Related Product Guide:
Things to Know About Pipe Fitting Works
How to Replace a Hydraulic Hose Fitting

Our enterprise insists all along the standard policy of "product good quality is base of organization survival; client gratification could be the staring point and ending of an enterprise; persistent improvement is eternal pursuit of staff" and the consistent purpose of "reputation to start with, purchaser first" for Factory selling 90011-Swaged Hose Fiting for Boston Importers, The product will supply to all over the world, such as: Nicaragua , Swaziland , Slovakia , Welcome to visit our company and factory, there are various products displayed in our showroom that will meet your expectation, meanwhile, if you are convenient to visit our website, our sales staff will try their efforts to provide you the best service


  • From http://www.kevincaron.com – Artist Kevin Caron shares how to fill a gap – and why you really shouldn’t ….

    Caron first addresses why you should avoid gaps altogether. It’s always better to make sure your fit is right, with straight lines, smooth cuts and tight joints, getting your fit up and prep done first. He explains that a tight fit leads to a good weld structurally. That’s not as important, perhaps, with something like art, but if you are building buildings or bridges, for example, it has to be a good joint. The weld will be X-rayed and inspected for soundness, porosity, gaps, etc. The space in a gap lets air come up and cause porosity because you’re super-heating the air above and below the gap and have a puddle of molten metal that pulls the air up through the gap and into the weld. By not having a good, tight joint, you’re causing more problems for yourself. Caron says a good fit is just part of being a good welder.

    Regardless, Caron shows you how to fill a gap. He sets up two pieces of 1/4″ plate with a V-gap, with one end fairly close and the other end wide. Again, he emphasizes that this is for aesthetic, not structural welding.

    Using Longevity’s ProMTS 200 because he loves the MIG welder in it, Caron first gives the metal a few tacks so the steel won’t move. Next he’s ready to run a welding bead. He’s got the MIG welder set at 23 volts for weld tacking, so he’s going to turn it down a little to 21.5, but leave the wire feed as it is at 147. Caron reminds us that, with this machine, that doesn’t mean 147 inches a minute (he’s not sure how Longevity measures wire speed), but it’s about two-thirds of the way up.

    Before Caron starts welding, though, he addresses whether you can just run your bead from one end to the other. He explains he wouldn’t. Because of the gap, he’s found that if you try to just run a bead from one end to the other, one piece of metal will move away as you are welding, so the gap actually widens. Caron says it’s best to tack it on one end, tack it on the other, then he likes to hopscotch back and forth. He’ll tack it in the middle, then run a short bead between two of the tacks, then go to another area and run a bead between two other tacks, etc., just filling it in as he works his way out. That helps spread out the heat more evenly and reduces warpage on thinner metals as well as prevents blow-outs. Caron then runs the bead.

    He says that that voltage worked well as he filled in the sections between the tacks. He also wove back and forth to fill in larger areas, “stealing” a little metal from each side of the gap. Then Caron shows the first weld at 21.5 volts and another at 21.2. From the back you can see that both welds got good penetration all the way through.

    A couple of other ways to fill gaps include straightening a coathanger and laying it inside the gap, getting a piece of thick copper -1/8″ or 1/4″ preferred – and using it as a backer because the steel won’t stick to the copper. You can clamp or prop the copper, which gives the molten steel something to run up against as you are welding. Depending upon your design, you could even back it with another piece of steel and just weld it in.

    For more how-to videos, visit http://www.kevincaron.com

    This supplier's raw material quality is stable and reliable, has always been in accordance with the requirements of our company to provide the goods that quality meet our requirements.
    5 Stars By Antonio from Botswana - 2015.06.21 17:11
    It is a very good, very rare business partners, looking forward to the next more perfect cooperation!
    5 Stars By Rachel from Indonesia - 2016.12.31 14:53

    Related Products

    WhatsApp Online Chat !