11 Years Manufacturer 1CM-WD-Metric Thread Bite Type Tube Fitting to Gambia Importers

METRIC THREAD WITH ED CAPTIVE SEALING( 1SO 99741-1)

METRIC THREAD BITE TYPE

See All Electric Pressure Washers: https://www.canadiantire.ca/en/automotive/pressure-washers.html

Electrically powered pressure washers are compact and easy to use.
Requiring minimal maintenance they excel at light and medium duty cleaning jobs.

Getting started is easy. Most models are ready go right away — just run out the pressure hose and connect the inlet. There are a few things to do before you start cleaning.
Before starting any job check the O-rings on the the spray hose. Replace any rings that are cracked.
Check that the inlet filter is free of debris so the pressure washer can deliver full cleaning power.
A useful accessory is this in-line filter. It prevents debris in the water line from clogging or damaging the pressure washer pump.
Before running the pressure washer turn on the tap and run water through the hose to wash out any dirt. Connect the hose and without turning on the pressure washer pull the trigger until a steady steam of water comes out.
Make sure that all fittings are tight.
And protect yourself with splash goggles.

Next select the right spray tip for the job.
The spray tip concentrates the water and creates a pattern that helps the cleaning action.
This red spray tip creates a pin-point stream for cleaning cracks and stubborn dirt.
The green tip is good for general cleaning duties.
The white tip creates a fan thats great for delicate cleaning.
And the black tip features a zero-pressure flow for applying detergents.
This pressure washer also has a turbo nozzle that creates an oscillating pattern for fast cleaning action
Plug the power cable into a GFCI protected receptacle. This type of receptacle has an internal circuit breaker that will trip if a ground fault current is detected.
Many electrical pressure washers can draw up to 13 amps so make sure no other appliances are sharing the same 15 amp circuit.
Well use the black tip for detergent application to wash this car.
This model has a reservoir for detergents and cleaning solutions.
Only use detergents designed for pressure washers. Fill to the recommended level.
Next Uncoil the pressure hose completely.
Turn on the pressure washer. The motor will pressurize the system then go into stand-by mode until you pull the spray gun trigger.
Stand just close enough so that the pressure washer evenly distributes the detergent.
Use a sweeping overlapping pattern to ensure complete cleaning.
When youre done shut of the feed valve and run the pressure washer until clear water comes out.
Drain the reservoir of any unused detergent
Coil the spray hose. This keeps it from getting kinked.

Store the power cable using the built in hooks. This will keep it safe from damage.

All pressure washers need to be winterized so that they arent damaged by freezing water.
Disconnect the inlet hose and run the pressure washer for a short time to purge the pump.
This aerosol antifreeze makes winterizing easy.
Attach the adapter and aerosol container to the inlet of the pressure washer and press to release the antifreeze.
Wait until the antifreeze fills the pump and exits the pressure washer as described in the antifreeze product manual.
Clean up any spills right away. Antifreeze can harm pets and animals.
Youre ready to clean when the warn weather returns.
Electric or Gas you can see a wide range of pressure washers and accessories at…
…Canadian Tire

In this video we show How to replace the oxygen (O2) sensor also known has Air Fuel Ratio sensor on the Nissan Frontier V6 (3300 – VG33E) engine.Here you will see the difference between Bank #1 (right side)and Bank #2(left side) heated (4-wire) oxygen sensors. Replacing the oxygen sensor every 60-70,000 miles is an effort to help conserve fuel/gasoline.The oxygen sensor are not the only device to harness against waste consumption. The coolant temperature sensor at the thermostat housing reports to the computer, the computer commands the cooling fans through the fuel/relay box. Some model will be equipped with dual cooling fans. One for normal operation is the 1st fan. The 2nd fan is for air condition operation and over-heating conditions. If the Tstat remain stuck “close” the two fan will operate and coolant will overflow in its reserve container. The Tstat ONLY control engine temperature. The fans operation and gauge help radiates any heat or over heating base on ambient air temperature and operator.

The oxygen sensor is a state EPA “enviromental term” all so known has a EGT – exhaust gas temperature sensor sends millivoltage(data) to the ecm – engine control module for fuel injector control and its flow rate(impedeance). The oxygen sensor key roll is to measure the combustion flame/temperature .the ideal temperature for anything above 75% throttle is .870mv – .900mv output at the exhaust gas temperature/oxygen sensor. The oxygen(o2) sensor also work in conjuction with the Mass Air Flow Meter/sensor for fuel injector control. So the oxygen sensor can also be conside a Air Fuel Ratio sensor and the Mass Air Flow meter is mounted on the intake manifold duct.

M18 sensors – Install finger tight then 1/2 – 3/4 turn with wrench/ O2 sensor socket.26-33ft. lbs
M12 sensors – Install finger tight then 3/4 – 1 turn with wrench / O2 sensor socket.13.2-17ft. lbs.

APPLICATION: 2003 NISSAN FRONTIER EX, Xterra
3300 CC ENGINE 4X4

PLEASE – RATE – COMMENT AND SUBSCRIBE.

* DO NOT drop or use an oxygen sensor that has been dropped as this may have caused shock damage to the ceramic cell.
* DO NOT use any compound on or around the sensor unless labeled as oxygen sensor friendly products.
* DO NOT use impact wrench or conventional socket type wrench to install sensor.
* DO NOT allow sensor or lead wire to touch exhaust manifold or any other hot component.
* DO NOT expose this product to water,oil,windshield cleaner, anti-corrosion oil,grease,terminal cleaner, etc.
* DO NOT use leaded fuels, silicone or metal based additives
* DO NOT store under high humidity conditions will promote rusting.
WARNING : Anti-seize compound may cause irritation to the skin or eyes. In case of contact, wash affected area with soap and water. In case of eye contact, Flush with water for 15 minutes. If irritation persists, consult a physician. If swallowed, DO NOT induce vomiting.

KEEP OUT OF REACH OF CHILDREN.